Skip to main content

VMware Workstation 14 Bridge Mode not Connected to Internet

Hello again friends and readers (don't know how many of you read my writings, but whateva)

I recently encountered a problem where everytime I tried to set my vm on pc to Bridge mode, it will always not connected to internet.

At first I thought it was the image problem, but after several time of deleting and installing VM, I realised that that is not my actual problem.

Then after several minutes of internet surfing, I found some other folks with similar problem with me, and there is actually solution for that.
https://communities.vmware.com/thread/580135

In short, what you need to do are:
-- Be sure your vm is stopped.
--Run the VMWare Virtual Network Editor
(click start and search for Virtual Network Editor)
-- Run it as administrator (or click the button at the bottom of the screen that says, "change settings." VMNet0 will dislpay when running as administrator. Otherwise, it will not be visible)
-- Highlight VMNet0 and click on "Automatic Settings"
-- You will see a list of adapters. De-select all but the physical network card. (When I set up up with player, I had selected only the 1.  After install of workstation, all of the items were checked.)
-- Click "OK"
-- Click "Ok"
-- Start the VM and test.



p/s: I will update this post with some pics for guide soon.

Comments

Popular posts from this blog

Memilih Kamera Pertama Anda. Bahagian 2 Tambahan - Kamera Point and Shoot

Edisi Khas untuk kamera Point and Shoot. Penulis merasakan kamera jenis ini tidak mendapat perhatian yang baik dengan ciri yang kompak, ringan dan mudah dibawa. Kebanyakan keluaran lewat 2015 mempunyai spesifikasi yang bagus, setara dengan DSLR dan Mirrorless. Contoh Kamera Point and Shoot keluaran Sony yang terkini bernama Sony ZV-1 Saiz Sensor - Kebanyakan kamera sebegini sensor sebesar 1 inci sehingga APS-C.  Megapixel - Normalnya bermula 12 MP sehingga 26 MP. Hasil gambar juga baik, cuma kekurangan fungsi Penstabil (Stabiliser) menyebabkan kualiti gambar adalah bergantung kepada tetapan (setting) yang betul serta tangan pengambil gambar yang teguh. Saiz Kamera - Kerana saiz yang kompak, ia senang dibawa kemana-mana sahaja, tanpa memakan ruang pada beg mahupun poket. Saiz kecil juga nampak natural, tidak seakan menceroboh momen dengan saiz yang besar, membuatkan orang berasa tidak senang duduk. Versatil - Mempunyai kebolehan merakam video, jadi

ARP for Dummy like Me!

ARP used to map IP address to MAC address on data link layer. It mainly used when Host is connected over Ethernet. In long explanation, This protocol used to locate address of a Host (Physical/Virtual) in network.  The address is searched or "resolved" by sending an "information" to a server (other host).  The server after received the information will then identify itself and respond back with the network information.  The responded information contain the required address.  This always happen over Ethernet. Ethernet address dependent to the hardware which is Network Interface card. So, during ARP request, it try to ask which IP associated with which MAC address. If you have used wireshark, maybe you can remember on Info section, there are always message saying "Who has $IP". For example:  Situation where ARP is used. Someone with IP X.X.X.X try ping $IP = Y.Y.Y.Y. We assume, the source PC did not have the IP information from the Targe

TWRP cannot flash Magisk on Redmi 4x

I tried flash an Android phone with TWRP as its bootloader and it keep rejecting to install Magisk. So this is how I solve it. (Tested on 23 August 2018 on Redmi 4x AOSP Extended v5.7) 1. In TWRP, go to : Home -> Mount -> select Cust (if not selected) -> Home 2. Then go back to main TWRP page, later: Home -> Advanced ->Terminal -> run following commands a. mount | grep cust -> It will show something like this /dev/block/mmcblk0xxx on /cust type ext4 .... -> copy the directory, and save it somewhere else. b. umount /cust -> go back to Home -> Mount -> uncheck Cust -> Home c. Go back to Advanced ->Terminal -> run following commands mount -t ext4 -o ro /dev/block/mmcblk0xxx /vendor 3. Finally go to Home -> Install and locate your magisk .zip file to flash it. Note: What if you already format the storage due to TWRP keep asking for password to decrypt storage despite you never encrypt it in the first place. (This is common